8/10/2020 0 Comments Fanuc Ot Control Manual
You possess to arranged 709 to the range from the throw to reference place. 7091955800. Today Z0 is the face of the chuck and reference position is Z end of the stroke.If you perform not obtained the e-mail, check out your junk email, also test to sign-up again (maybe you skip came into your e-mail deal with which is usually why you do not receive the email.
To register click right here sign-up before you can post: click the sign up hyperlink above to continue. ![]() Specifically, there provides always been recently a workshift value of someplace around Z .-20.000 to -30.000 and if I operate a program with a Gary the gadget guy28 Z .0 command, the carriage will take off seemingly for a place somewhere beyond the tailstock of the machine. ![]() Ive examine through the manual, but I possess no hint what they are usually saying. Fanuc Ot Control Manual Concerning TheNevertheless, I did discover some information in the Operators Manual concerning the heart stroke limits (variables 700-701 and 704-705). Those values are: 700 (Upper X limit) 4000 701(Top Z . limit) 2000 704 (Lower X limit) -516000 705 (Lower Z limit) -1955000 Ill make the risky assumption that the values are in mm with the last three values being to the right of a decimal -- So Z would have a total stroke of 1957mm or 77.047. That sounds about correct provided the duration of the methods, but when I jog the buggy down to about the finish of the ways, the (Machine) place scans -669.950. That cant end up being right. I would imagine that the manufacturer of the machine established a device Z .0 coordinate somewhere along the physical range of the machine and not a good 20 yards beyond the spindle. I approved this by running the Z axis in.001 installments and noting thát for every.001 moved, the device position screen shifts.025(mm). Today, Im thinking why this would take place therefore if you have any concepts, I would value your insight. It is usually only the machine position configurations that display a metric value. Stevo, I attempted a Gary the gadget guy28 Watts0 (in MDI mode)and it minds off in the exact same path and length as a G28 Z0. I looked over the programs that our additional lathe guy had operate lately and he fundamentally just transmits it to a secure Z distance from his program Z0 (e.h. H0 G90 Z10.) -Norb. It can be done possibly or and most people place it in thé workshift bécause it can be easier. A few items to consider. Gary the gadget guy28G91W0. Also consider the Gary the gadget guy28W0 with the common workshift established to 0 in the Z. Your 1scapital t reference place is not set correctly along with your softlimit configurations. To muddy the oceans a little bit you are usually comping for the troubles in your common offset. Provided that I are really surprised that the G28W0 do not work when you healed the typical to zero. The just point that I can think of is maybe you have something in H54 which will be generally default on thé Fanucs ánd it is taking that in to accounts as nicely. For 1 I would like to know when you system Gary the gadget guy28W0 with the worth in the common and with it set to zero will to your length to go transformation on your screen between the 2. ![]() Today your reference position will be Z end of thé stroke which yóu say is abóut 75-80 from the chuck. IOW home is established to the center of your stroke and you are comping the relaxation in your typical offset. With 705-1955.000 or 76.9685 your softlimit environment will not really alarm system until after you strike the chuck. And 7012000 or even.0787 which should softlimit alarm simply above home position. The appropriate way to arranged these beliefs is usually as follows, ór I should state the method that I set up machine tools. If guide position can be Z end of stroké and lets sáy that you havé 77 of stroke between reference position and the face of the chuck. You have to set 709 to the distance from the throw to reference position. Now Z .0 is the face of the chuck and reference position is Z end of the stroke.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |